Lighting makes up a huge portion of energy expenses. This bundle provides complete control over various lighting throughout a home. Apply these control devices whether the home has an HAI home automation controller or not (requires UPStart software and PIM to PC Cable). Makes for a great first taste of home automation and can be expanded upon as homeowner needs grow. A Scene Switch can be set to operate multiple lighting settings with the push of a single button. 110 VAC only.

INCLUDED WITH PACKAGE

• 35A00-1: 600W UPB Dimmer Switches (24) - The 600 Watt UPB Dimmer Switch is used for controlling and dimming lighting loads up to 600 Watts. It comes with a default white paddle, connectors, and instructions. These switches may be changed from a Dimmer mode to a Non-Dimming mode.
• 37A00-1: Auxiliary Switches (6) - The Auxiliary Switch can be used with any HLC Switch to make "three-way" (two switches control one light) and multi-way (more than two switches control one light) using conventional "three-way" wiring techniques.
• 59A00-1: UPB Lamp Modules (4) - The HAI UPB Lamp Module is a plug-in dimmer that incorporates the UPB two-way powerline communication technology, which gives it the ability to be remotely controlled by UPB compatible controllers. The Lamp Module has one UPB controllable outlet that can sense the lamp's local on/off switch to turn the lamp on even after it was turned off using UPB control. The HAI UPB Lamp Module is also capable of transmitting UPB messages (including current light level) when the local lamp switch is used to turn the lamp on.
• 40A00-1: 15A Relay Switches (2) - The 15A Relay UPB Switch is used for controlling non-dimming loads and is ideal for heavier loads or for motors (like ceiling fans) that may hum when used with Dimming or Non-Dimming switches. It comes with a default white paddle, connectors, and instructions.
• 38A00-1: Scene Switch, 6-Button (2) - Control all lights in a room or area. Lights may be turned on or off, dimmed, brightened, and set to four different scenes. Setting a scene is as simple as pressing the scene button the Scene Switch five times. Has Infrared Receiver for use with Scene Switch Remote Control. Includes White Bezel, connectors, instructions.
• 38A15-WH: Table Top Scene Switch Cradles, White (2) - The HAI 38A15 Table Top Scene Switch Cradle is used to mount the HAI 38A00-1 HLC Scene Switch, 38A00-2 HLC House Status Switch, or 38A00-3 Lumina Mode Switch in a table top application.
• 39A00-2: UPB Split Phase Repeater (1) - Designed to repeat UPB signal in installations requiring additional signal strength. Must be used on a 120/240VAC split-phase 60Hz powerline.
• 38A14-1: Scene Switch Remotes (2) - The Model 38A14-1 Scene Switch Remote Control is used for controlling rooms of HLC lighting by sending infrared (IR) signals to Model 38A00-1 6-Button Scene Switches with IR Receivers. To activate lighting, point the 38A14-1 Remote Control at a 38A00-1 Scene Switch and press the desired buttons. The buttons on the 38A14-1 Remote Control simulate pressing the pushbuttons on the 38A00-1 Scene Switch with IR Receiver. The room can be turned on, turned off, dimmed, brightened, or set to a scene (A-D). The Model 38A14-1 Scene Switch Remote Control has 4 separate IR codes for each button so that it can be used to control up to 4 Model 38A00-1 Scene Switches with IR Receivers located in the same general area of a room.
• 36A00-1: UPB Powerline Interface Module with Cable (1) - This PIM connects the UPB lighting system to an automation system or computer, which can then control the lights. The PIM makes the lighting system accessible through the home computer or from a remote location over the Internet. Comes with a cable for connecting the PIM to a serial port on an HAI home control system.